Your Vehicle: 2001 Ford Escort ZX2 L4-2.0L DOHC VIN 3
 
Vehicle » Powertrain Management » Computers and Control Systems » Testing and Inspection » Programming and Relearning » Flash Electrically Erasable Programmable Read Only Memory (EEPROM)  
 
 
  Flash Electrically Erasable Programmable Read Only Memory (EEPROM)  
 

Flash Electrically Eraseable Programmable Read Only Memory - Flash EEPROM

Description

Flash Electrically Eraseable Programmable Read Only Memory (EEPROM) is contained in an Integrated Circuit (IC) internal to the Powertrain Control Module (PCM) . The EEPROM contains the vehicle strategy including calibration information specific to the vehicle and is capable of being reprogrammed or reflashed repeatedly.

As part of the calibration there is an area referred to as the Vehicle Identification (VID) block. The VID block must be programmed when replacing the PCM as under Programming the VID Block for a Replacement PCM. Failure to perform this procedure may generate fault code: P1639, VID Block not programmed or is corrupt. The VID block in an existing Powertrain Control Module (PCM) . can also be tailored to accommodate various hardware changes made to the vehicle since production. Failure to perform this procedure properly may generate fault code: P1635, Tire/Axle Ratio out of Acceptable Range. This is described under Making Changes to the VID Block and also under Making Changes to the PCM Calibration. The VID block contains many items used by the strategy for a variety of functions. Some of these items include the VIN number, octane adjust, fuel octane, fuel type, vehicle speed limit, tire size, axle ratio, the presence of speed control and four wheel drive electronic shift on the fly versus manual shift on the fly. Only items applicable to vehicle hardware and supported by the VID block will be displayed on the scan tool.

When changing items in the VID block, the strategy will place range limits on certain items such as tire and axle ratio. The VID block is also limited to the number of times to be reconfigured. When this limit is reached, the scan tool will display a message indicating the need to flash the PCM again to reset the VID block.

Each of the procedures described below use the Worldwide Diagnostic System (WDS) . Reprogramming can be performed by a local Ford dealer for any non Ford facility. There are other Enhanced Scan Tools that may have reprogramming capabilities available. Refer to the diagnostic tool manufacturers users manual for details.

Programming the VID Block for a Replacement PCM
A new PCM will contain the latest strategy and calibration level for a particular vehicle. However, the VID block will be blank and will need programming. There are two procedures available. The first is an automatic data transfer from the old PCM to the new PCM and the second is manual data entry into the new PCM.

Automatic data transfer will be performed if the old PCM is capable of communicating. This is done by the use of a scan tool to retrieve data from the old PCM before removing it from the vehicle. The stored data can now be downloaded to the new PCM after it has been replaced.

Manual data entry must be performed if the old module is damaged and is incapable of communicating. Remove and replace the old PCM. You may be instructed to contact the "AS BUILT" data center for the information needed to manually update the VID block with the scan tool. Contact the center ONLY if the old PCM cannot be used or the data is corrupt. For Ford L-M technician's, contact your National Hotline for "AS Built" data. Non Ford technicians, use the Fed World website at "fedworld.gov". Select Auto Service Information and search for "Calibrations" or "Vehicle Calibrations" then specify vehicle manufacturer, model name and model year as required.

Making Changes to the VID Block
A PCM which is programmed may require changes to be made to certain VID information to accommodate vehicle hardware. Refer to PCM/Module Reprogramming on the Scan Tool.

Making Changes to the PCM Calibration
At certain times, the entire EEPROM will need to be completely reprogrammed. This is due to changes made to the strategy or calibration after production or the need to reset the VID block because it has reached its limit. Refer to PCM/Module Reprogramming on the Scan Tool.