Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » B Code Charts » B2612 » Sedan With Intelligent Key  
 
 
  Sedan With Intelligent Key  
 

B2612 STEERING STATUS

Description
There are 2 switches in the electronic steering column lock. IPDM E/R compares those 2 switches conditions to judge the present steering status and transmit the result to BCM via CAN communication.

DTC Logic

DTC DETECTION LOGIC

NOTE:

  

DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE 1

  1. Press the push-button ignition switch under the following conditions and wait for at least 1 second.
    • CVT selector lever is in the P or N position.
    • Do not depress brake pedal.
    • Steering is locked.
  1. Check "Self diagnostic result" with CONSULT-III. Is DTC detected?

YES >> Refer to Diagnosis Procedure.
NO >> GO TO 2
2.PERFORM DTC CONFIRMATION PROCEDURE 2

  1. Turn ignition switch ON.
  2. Turn ignition switch OFF.
  3. Press door switch.
  4. Check "Self diagnostic result" with CONSULT-III. Is DTC detected?

YES >> Refer to Diagnosis Procedure.
NO >> Inspection End.

Diagnosis Procedure
1.Inspection START
Check the case in which DTC is detected.

  • Case1: It is detected after ignition switch is changed from ON to OFF and door switch is pressed.
  • Case2: It is detected after ignition switch is changed from ON to OFF In which case is DTC detected?

Case1 >> GO TO 2
Case2 >> GO TO 7
2.CHECK BCM OUTPUT SIGNAL

  1. Turn ignition switch OFF.
  2. Disconnect electronic steering column lock harness connector and IPDM E/R harness connector.

  

  1. Check voltage between electronic steering column lock harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 4
NO >> GO TO 3
3.CHECK ELECTRONIC STEERING COLUMN LOCK CIRCUIT-I

  1. Disconnect BCM harness connector.

  

  1. Check continuity between BCM harness connector M19 (A) terminal 85 and electronic steering column lock harness connector M32 (B) terminal 3.

  

  1. Check continuity between BCM harness connector M19 (A) terminal 85 and ground.

  

Is the Inspection result normal?
YES >> GO TO 6
NO >> Repair harness or connector.
4.CHECK IPDM E/R OUTPUT SIGNAL

  1. Connect IPDM E/R harness connector.
  2. Disconnect BCM harness connector.

  

  1. Check voltage between electronic steering column lock harness connector and ground.

  

Is the Inspection result normal?
YES >> Replace electronic steering column lock.
NO >> GO TO 5
5.CHECK ELECTRONIC STEERING COLUMN LOCK CIRCUIT-II

  

  1. Check continuity between electronic steering column lock harness connector M32 (A) terminal 3 and IPDM E/R harness connector E18 (B) terminal 32.

  

  1. Check continuity between electronic steering column lock harness connector M32 (A) terminal 3 and ground.

  

Is the Inspection result normal?
YES >> GO TO 6
NO >> Repair harness or connector.
6.CHECK INTERMITTENT INCIDENT
Refer to See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Intermittent Incident.
>> Inspection End.
7.CHECK BCM OUTPUT SIGNAL

  1. Turn ignition switch OFF.
  2. Disconnect electronic steering column lock harness connector and IPDM E/R harness connector.

  

  1. Check voltage between electronic steering column lock harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 9
NO >> GO TO 8
8.CHECK ELECTRONIC STEERING COLUMN LOCK CIRCUIT-I

  1. Disconnect BCM harness connector.

  

  1. Check continuity between BCM harness connector M19 (A) terminal 86 and electronic steering column lock harness connector M32 (B) terminal 8.

  

  1. Check continuity between BCM harness connector M19 (A) terminal 86 and ground.

  

Is the Inspection result normal?
YES >> GO TO 11
NO >> Repair harness or connector.
9.CHECK IPDM E/R OUTPUT SIGNAL

  1. Connect IPDM E/R harness connector.
  2. Disconnect BCM harness connector.

  

  1. Check voltage between electronic steering column lock harness connector and ground.

  

Is the Inspection result normal?
YES >> Replace electronic steering column lock.
NO >> GO TO 10
10.CHECK ELECTRONIC STEERING COLUMN LOCK CIRCUIT-II

  

  1. Check continuity between electronic steering column lock harness connector M32 (A) terminal 8 and IPDM E/R harness connector E18 (B) terminal 33.

  

  1. Check continuity between electronic steering column lock harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 11
NO >> Repair harness or connector.
11.CHECK INTERMITTENT INCIDENT
Refer to See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Intermittent Incident.
>> Inspection End.