Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » B Code Charts » B2110 » Sedan With Intelligent Key  
 
 
  Sedan With Intelligent Key  
 

B2110 PNP/CLUTCH INTERLOCK SWITCH

Description
IPDM E/R confirms the shift position with the following signals.

  • Park/neutral position (PNP) switch (CVT models)
  • Clutch inter lock switch (M/T models)
  • Shift position signal from BCM (CAN)

DTC Logic

DTC DETECTION LOGIC

NOTE:

  

DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn the ignition switch ON under the following conditions and wait for at least 1 second.
    • CVT selector lever is in the P or N position
    • Do not depress the brake pedal
  1. Check "Self diagnostic result" with CONSULT-III. Is DTC detected?

YES >> Refer to Diagnosis Procedure.
NO >> Inspection End.

Diagnosis Procedure
1.Inspection START
Check which type of transmission the vehicle is equipped with.
Which type of transmission
CVT >> GO TO 2
M/T >> GO TO 5
2.CHECK DTC WITH BCM
Refer to See: Testing and Inspection.
Is the Inspection result normal?
YES >> GO TO 3
NO >> Repair or replace malfunctioning parts.
3.CHECK PNP SWITCH INPUT SIGNAL

  1. Turn ignition switch OFF.
  2. Disconnect IPDM E/R harness connector.
  3. Turn ignition switch ON.

  

  1. Check voltage between IPDM E/R harness connector and ground under following condition.

  

Is the Inspection result normal?
YES >> Replace IPDM E/R. Refer to See: Power and Ground Distribution\Power Distribution Module\Service and Repair.
NO >> (VQ35DE) GO TO 4
NO >> (QR25DE) GO TO 10
4.CHECK PNP SWITCH CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect TCM harness connector.

  

  1. Check continuity between IPDM E/R harness connector and TCM harness connector.

  

  1. Check continuity between TCM harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 13
NO >> Repair harness or connector.
5.CHECK CLUTCH INTERLOCK SWITCH INPUT SIGNAL (BCM)

  1. Turn ignition switch OFF.
  2. Disconnect BCM harness connector.

  

  1. Check voltage between BCM harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 6
NO >> GO TO 7
6.CHECK CLUTCH INTERLOCK SWITCH INPUT SIGNAL

  1. Turn ignition switch OFF.
  2. Disconnect IPDM E/R harness connector.
  3. Turn ignition switch ON.

  

  1. Check voltage between IPDM E/R harness connector and ground.

  

Is the Inspection result normal?
YES >> Replace the IPDM E/R. Refer to See: Power and Ground Distribution\Power Distribution Module\Service and Repair.
NO >> Check harness for open between clutch interlock switch and IPDM E/R.
7.CHECK CLUTCH INTERLOCK SWITCH POWER SUPPLY

  1. Disconnect clutch interlock switch harness connector.

  

  1. Check voltage between clutch interlock switch harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 8
NO >> Check harness for open or short between clutch interlock switch and fuse.
8.CHECK CLUTCH INTERLOCK SWITCH CIRCUIT

  

  1. Check continuity between IPDM E/R harness connector and clutch interlock switch harness connector.

  

  1. Check continuity between clutch interlock switch harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 9
NO >> Repair harness or connector.
9.CHECK CLUTCH INTERLOCK SWITCH
Refer to Component Inspection.
Is the Inspection result normal?
YES >> Replace the IPDM E/R. Refer to See: Power and Ground Distribution\Power Distribution Module\Service and Repair.
NO >> Replace clutch interlock switch.
10.CHECK PNP SWITCH CIRCUIT FOR CONTINUITY

  1. Turn ignition switch OFF.

  

  1. Check continuity between IPDM E/R harness connector terminals 72 and 74.

  

Is the Inspection result normal?
YES >> GO TO 11
NO >> GO TO 12
11.CHECK PNP SWITCH CIRCUIT FOR SHORT

  

Check continuity between IPDM E/R harness connector terminals
72, 74 and ground.

  

Is the Inspection result normal?
YES >> Replace the IPDM E/R. Refer to See: Power and Ground Distribution\Power Distribution Module\Service and Repair.
NO >> Repair or replace harness.
12.CHECK PNP SWITCH INPUT SIGNAL CIRCUIT

  1. Disconnect PNP switch harness connector.

  

  1. Check continuity between PNP switch and IPDM E/R harness connectors.

  

  1. Check continuity between PNP switch harness connector and ground.

  

Is the Inspection result normal?
YES >> Replace PNP switch.
NO >> Repair harness or connector.
13.CHECK INTERMITTENT INCIDENT
Refer to See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Intermittent Incident.
>> Inspection End.

Component Inspection
1.CHECK CLUTCH INTERLOCK SWITCH

  1. Turn ignition switch OFF.
  2. Disconnect clutch interlock switch harness connector.

  

  1. Check continuity between clutch interlock switch under the following conditions.

  

Is the Inspection result normal?
YES >> Inspection End.
NO >> Replace clutch interlock switch.