Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » Instrument Panel, Gauges and Warning Indicators » Dashboard / Instrument Panel » Service and Repair » Removal And Installation  
 
 
  Removal And Installation  
 

INSTRUMENT PANEL ASSEMBLY

Removal and Installation

CAUTION:

  • Disconnect both battery terminals.
  • Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
  • Be careful not to scratch instrument panel pad and other parts.

REMOVAL

  1. Disconnect both battery terminals.
  2. Remove the A-pillar finishers. Refer to See: Body and Frame\Interior Moulding / Trim\Trim Panel\Service and Repair\Removal And Installation\Coupe.
  3. Put selector lever in the drive (D) position, then remove selector lever knob (CVT Models only). Refer to See: Transmission and Drivetrain\Continuously Variable Transmission/Transaxle\Shifter CVT\Service and Repair\CVT RE0F09B\Removal And Installation.
  4. Put the shift lever in neutral, then remove shift lever knob. (M/T Models only) Refer to See: Transmission and Drivetrain\Manual Transmission/Transaxle\Shifter M/T\Service and Repair\Removal And Installation.

  

  1. Remove the cluster lid D (1).
  2. Remove console finisher. Refer to See: Transmission and Drivetrain\Continuously Variable Transmission/Transaxle\Shifter CVT\Service and Repair\CVT RE0F09B\Removal And Installation.

  

  1. Remove the storage bin (1) or CD changer finisher (if equipped).
  2. Remove both instrument side masks (1).

  

  1. Open the fuse block cover, remove the instrument lower cover screw (A), then remove the instrument lower cover (1).
    • Disconnect the harness connectors.
    • Disconnect the aspirator tube.

  

  1. Remove both the console side finishers.

  

  1. Remove the console upper screws (A).
  2. Remove the console side screws (A).

  

  1. Remove both the console rear screw covers, then remove the rear screws (A), then remove the console assembly.

  

  

  1. Open the glove box door (1), remove the glove box assembly screws (A).

  

  1. Remove the glove box assembly lower screws (A), then remove the glove box assembly.
  2. Remove the steering wheel. Refer to See: Steering and Suspension\Steering\Steering Wheel\Service and Repair\Removal and Replacement.

  

  1. Remove the steering column screws (A), then remove both the steering wheel column upper (1) and lower (2) covers.

  

  1. Remove the cluster lid A (1).

  

  1. Remove the combination meter screws (A), then remove the combination meter (1).
    • Disconnect the harness connector.
  1. Remove the spiral cable. Refer to See: Restraints and Safety Systems\Air Bag Systems\Clockspring Assembly / Spiral Cable\Service and Repair.
  2. Remove the combination switch. Refer to See: Sensors and Switches\Sensors and Switches - Wiper and Washer Systems\Windshield Washer Switch\Service and Repair.

  

  1. Remove the center ventilator grilles (1).

  

  1. Remove the cluster lid C assembly upper and lower screws (A), then remove the cluster lid C assembly (1).
    • Disconnect the harness connectors.
  1. Remove both tweeter speaker grilles and disconnect the harness connectors.

  

  1. Remove the passenger air bag bolt (A).

  

  1. Remove the remaining instrument panel screws (A).
  2. Disconnect the audio harness connector located near the RH A-pillar.
  3. Lift the instrument panel high enough in order to disconnect all the necessary harness connectors, then remove the instrument panel.

INSTALLATION
Installation is in the reverse order of removal.

  • If replacing the Instrument panel transfer all the necessary parts to the new instrument panel.