Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » P Code Charts » P0032  
 
 
  P0032  
 

P0031, P0032, P0051, P0052 A/F SENSOR 1 HEATER

Description

SYSTEM DESCRIPTION

  

The ECM performs ON/OFF duty control of the A/F sensor 1 heater corresponding to the engine operating condition to keep the temperature of A/F sensor 1 element within the specified range.

DTC Logic

DTC DETECTION LOGIC

  

DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds. TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 10 seconds.
  2. Check 1st trip DTC. Is 1st trip DTC detected?

YES >> Go to Diagnosis Procedure.
NG >> Inspection END

Diagnosis Procedure
1.CHECK GROUND CONNECTION

  1. Turn ignition switch OFF.
  2. Check ground connection E9. Refer to Ground Inspection in See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Circuit Inspection. Is the Inspection result normal?

YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT

  1. Disconnect air fuel ratio (A/F) sensor 1 harness connector.
  2. Turn ignition switch ON.

  

  1. Check the voltage between A/F sensor 1 harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.DETECT MALFUNCTIONING PART
Check the following.

  • IPDM E/R harness connector F10
  • 15 A fuse (No. 37)
  • Harness for open or short between A/F sensor 1 and fuse >> Repair or replace harness or connectors.

4.CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check harness continuity between A/F sensor 1 harness connector and ECM harness connector.

  

  1. Also check harness for short to ground and short to power. Is the Inspection result normal?

YES >> GO TO 5.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
5.CHECK A/F SENSOR 1 HEATER
Refer to Component Inspection.
Is the Inspection result normal?
YES >> GO TO 7.
NO >> GO TO 6.
6.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ratio (A/F) sensor 1.

CAUTION:

  • Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
  • Before installing new A/F sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant (commercial service tool).

>> Inspection END
7.CHECK INTERMITTENT INCIDENT
Perform See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Intermittent Incident.
>> Inspection END

Component Inspection
1.CHECK AIR FUEL RATIO (A/F) SENSOR 1
Check resistance between A/F sensor terminals as per the following.

  

Is the Inspection result normal?
YES >> Inspection END
NO >> GO TO 2.

  

2.REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ratio (A/F) sensor 1.

CAUTION:

  • Discard any (A/F) sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
  • Before installing new (A/F) sensor, clean exhaust system threads using Heated Oxygen Sensor Thread Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant (commercial service tool).

>> Inspection END