Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » P Code Charts » P0103  
 
 
  P0103  
 

P0102, P0103 MAF SENSOR

Description

  

The mass air flow sensor (1) is placed in the stream of intake air. It measures the intake flow rate by measuring a part of the entire intake flow. The mass air flow sensor controls the temperature of the hot wire to a certain amount. The heat generated by the hot wire is reduced as the intake air flows around it. The greater air flow, the greater the heat loss.
Therefore, the electric current supplied to hot wire is changed to maintain the temperature of the hot wire as air flow increases. The
ECM detects the air flow by means of this current change.

DTC Logic

DTC DETECTION LOGIC

  

DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds. Which DTC is detected?

P0102 >> GO TO 2.
P0103 >> GO TO 3.
2.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0102

  1. Start engine and wait at least 5 seconds.
  2. Check DTC. Is DTC detected?

YES >> Go to Diagnosis Procedure.
NO >> Inspection END
3.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0103-I

  1. Turn ignition switch ON and wait at least 5 seconds.
  2. Check DTC. Is DTC detected?

YES >> Go to Diagnosis Procedure.
NO >> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P0103-II

  1. Start engine and wait at least 5 seconds.
  2. Check DTC. Is DTC detected?

YES >> Go to Diagnosis Procedure.
NO >> Inspection END

Diagnosis Procedure
1.Inspection START
Confirm the detected DTC.
Which DTC is detected?
P0102 >> GO TO 2.
P0103 >> GO TO 3.
2.CHECK INTAKE SYSTEM
Check the following for connection.

  • Air duct
  • Vacuum hoses
  • Intake air passage between air duct to intake manifold Is the Inspection result normal?

YES >> GO TO 3.
NO >> Reconnect the parts.
3.CHECK GROUND CONNECTION

  1. Turn ignition switch OFF.
  2. Check ground connection E9. Refer to Ground Inspection in See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Circuit Inspection. Is the Inspection result normal?

YES >> GO TO 4.
NO >> Repair or replace ground connection.
4.CHECK MAF SENSOR POWER SUPPLY CIRCUIT

  1. Disconnect mass air flow (MAF) sensor harness connector.
  2. Turn ignition switch ON.

  

  1. Check the voltage between MAF sensor harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 6.
NO >> GO TO 5.
5.DETECT MALFUNCTIONING PART
Check the following.

  • Harness connectors E11, F2
  • Harness for open or short between mass air flow sensor and ECM
  • Harness for open or short between mass air flow sensor and IPDM E/R >> Repair open circuit, short to ground or short to power in harness or connectors.

6.CHECK MAF SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between MAF sensor harness connector and ECM harness connector.

  

  1. Also check harness for short to ground and short to power. Is the Inspection result normal?

YES >> GO TO 7.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
7.CHECK MAF SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Check the continuity between MAF sensor harness connector and ECM harness connector.

  

  1. Also check harness for short to ground and short to power. Is the Inspection result normal?

YES >> GO TO 8.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
8.CHECK MASS AIR FLOW SENSOR
Refer to Component Inspection.
Is the Inspection result normal?
YES >> GO TO 9.
NO >> Replace mass air flow sensor.
9.CHECK INTERMITTENT INCIDENT
Refer to See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Intermittent Incident.
>> Inspection END

Component Inspection
1.CHECK MASS AIR FLOW SENSOR-I
With CONSULT-III

  1. Reconnect all harness connectors disconnected.
  2. Start engine and warm it up to normal operating temperature.
  3. Connect CONSULT-III and select "DATA MONITOR" mode.
  4. Select "MAS A/F SE-B1" and check indication under the following conditions.

  

Without CONSULT-III

  1. Reconnect all harness connectors disconnected.
  2. Start engine and warm it up to normal operating temperature.

  

  1. Check the voltage between ECM harness connector terminals under the following conditions.

  

Is the Inspection result normal?
YES >> Inspection END
NO >> GO TO 2.
2.CHECK FOR THE CAUSE OF UNEVEN AIR FLOW VIA THE MASS AIR FLOW SENSOR
Check for the cause of uneven air flow via the mass air flow sensor. Refer to the following.

  • Crushed air ducts
  • Malfunctioning seal of air cleaner element
  • Uneven dirt of air cleaner element
  • Improper specification of intake air system parts Is the Inspection result normal?

YES >> GO TO 4.
NO >> GO TO 3.
3.CHECK MASS AIR FLOW SENSOR-II
With CONSULT-III

  1. Repair or replace malfunctioning part.
  2. Start engine and warm it up to normal operating temperature.
  3. Connect CONSULT-III and select "DATA MONITOR" mode.
  4. Select "MAS A/F SE-B1" and check indication under the following conditions.

  

Without CONSULT-III

  1. Repair or replace malfunctioning part.
  2. Start engine and warm it up to normal operating temperature.

  

  1. Check the voltage between ECM harness connector terminals under the following conditions.

  

Is the Inspection result normal?
YES >> Inspection END
NO >> GO TO 4.
4.CHECK MASS AIR FLOW SENSOR-III
With CONSULT-III

  1. Turn ignition switch OFF.
  2. Disconnect mass air flow sensor harness connector and reconnect it again.
  3. Start engine and warm it up to normal operating temperature.
  4. Connect CONSULT-III and select "DATA MONITOR" mode.
  5. Select "MAS A/F SE-B1" and check indication under the following conditions.

  

Without CONSULT-III

  1. Turn ignition switch OFF.
  2. Disconnect mass air flow sensor harness connector and reconnect it again.
  3. Start engine and warm it up to normal operating temperature.

  

  1. Check the voltage between ECM harness connector terminals under the following conditions.

  

Is the Inspection result normal?
YES >> Inspection END
NO >> Clean or replace mass air flow sensor.