Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » P Code Charts » P0845  
 
 
  P0845  
 

P0845 TRANSMISSION FLUID PRESSURE SENSOR B (PRI PRESSURE SENSOR)

Description
The transmission fluid pressure sensor B (primary pressure sensor) detects primary pressure of CVT and sends TCM the signal.

DTC Logic

DTC DETECTION LOGIC

  

DTC CONFIRMATION PROCEDURE

NOTE:
If "DTC CONFIRMATION PROCEDURE" has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.CHECK DTC DETECTION
With CONSULT-III

  1. Turn ignition switch ON.
  2. Select "DATA MONITOR".
  3. Make sure that output voltage of line temperature sensor is within the range below.

ATF TEMP SEN : 1.0 - 2.0 V

If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid)

  1. Start engine and wait for at least 5 consecutive seconds. With GST

Follow the procedure "With CONSULT-III".
Is "P0845 TR PRS SENS/B CIRC" detected?
YES >> Go to Diagnosis Procedure.
NO >> Check intermittent incident. Refer to See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Intermittent Incident.

Diagnosis Procedure
1.CHECK INPUT SIGNAL

  

  1. Start engine.
  2. Check voltage between TCM harness connector F16 terminal 14 and ground.

  

  1. Turn ignition switch OFF. Is the Inspection result normal?

YES >> GO TO 8.
NO >> GO TO 2.
2.CHECK SENSOR POWER AND SENSOR GROUND

  

  1. Turn ignition switch ON.
  2. Check voltage between TCM harness connector F16 terminal 25 and 26.

  

Is the Inspection result normal?
YES >> GO TO 3.
NO >> GO TO 5.
3.CHECK HARNESS BETWEEN TCM AND CVT UNIT [TRANSMISSION FLUID PRESSURE SENSOR B (PRIMARY PRESSURE SENSOR)] (PART 1)

  

  1. Turn ignition switch OFF.
  2. Disconnect TCM harness connector and CVT unit harness connector.
  3. Check continuity between TCM harness connector F16 (A) terminal 14 and CVT unit harness connector F46 (B) terminal 25.

  

Is the Inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.CHECK HARNESS BETWEEN TCM AND CVT UNIT [TRANSMISSION FLUID PRESSURE SENSOR B
(PRIMARY PRESSURE SENSOR)] (PART 2)

  

Check continuity between TCM harness connector F16 terminal 14 and ground.

  

Is the Inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace damaged parts.
5.CHECK HARNESS BETWEEN TCM AND CVT UNIT (SENSOR POWER AND SENSOR GROUND) (PART 1)

  

  1. Turn ignition switch OFF.
  2. Disconnect TCM harness connector and CVT unit harness connector.
  3. Check continuity between TCM harness connector F16 (A) terminal 25, 26 and CVT unit harness connector F46 (B) terminal 19, 20.

  

Is the Inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace damaged parts.
6.CHECK HARNESS BETWEEN TCM AND CVT UNIT (SENSOR POWER AND SENSOR GROUND) (PART 2)

  

Check continuity between TCM harness connector F16 terminal 25, 26 and ground.

  

Is the Inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace damaged parts.
7.CHECK TCM

  1. Replace same type TCM. Refer to See: Powertrain Management\Transmission Control Systems\Control Module, CVT\Service and Repair\CVT RE0F09B\Exploded View.
  2. Connect each connector.
  3. Perform "DTC CONFIRMATION PROCEDURE". Refer to DTC Logic. Is "P0840 TR PRS SENS/A CIRC" detected?

YES >> Replace transaxle assembly. Refer to See: Transmission and Drivetrain\Continuously Variable Transmission/Transaxle\Service and Repair\CVT RE0F09B\Transaxle Assembly\Exploded View.
NO >> Replace TCM. Refer to See: Powertrain Management\Transmission Control Systems\Control Module, CVT\Service and Repair\CVT RE0F09B\Exploded View.
8.DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the Inspection result normal?
YES >> Replace TCM. Refer to See: Powertrain Management\Transmission Control Systems\Control Module, CVT\Service and Repair\CVT RE0F09B\Exploded View.
NO >> Repair or replace damaged parts.