Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » P Code Charts » P2135  
 
 
  P2135  
 

P2135 TP SENSOR

Description

  

Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc. The throttle position sensor responds to the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a kind of potentiometers which transform the throttle valve position into output voltage, and emit the voltage signals to the ECM. In addition, these sensors detect the opening and closing speed of the throttle valve and feed the voltage signals to the ECM. The ECM judges the current opening angle of the throttle valve from these signals and the
ECM controls the throttle control motor to make the throttle valve opening angle properly in response to driving condition.

DTC Logic

DTC DETECTION LOGIC

NOTE:
If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to See: P0643.

  

DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds. TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 1 second.
  2. Check DTC. Is DTC detected?

YES >> Go to Diagnosis Procedure.
NO >> Inspection END

Diagnosis Procedure
1.CHECK GROUND CONNECTION

  1. Turn ignition switch OFF.
  2. Check ground connection E9. Refer to Ground Inspection in See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Circuit Inspection. Is the Inspection result normal?

YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT-I

  1. Disconnect electric throttle control actuator harness connector.
  2. Turn ignition switch ON.

  

  1. Check the voltage between electric throttle control actuator harness connector and ground.

  

Is the Inspection result normal?
YES >> GO TO 3.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
3.CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

  

  1. Also check harness for short to ground and short to power. Is the Inspection result normal?

YES >> GO TO 4.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
4.CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

  

  1. Also check harness for short to ground and short to power. Is the Inspection result normal?

YES >> GO TO 5.
NO >> Repair open circuit, short to ground or short to power in harness or connectors.
5.CHECK THROTTLE POSITION SENSOR
Refer to Component Inspection.
Is the Inspection result normal?
YES >> GO TO 7.
NO >> GO TO 6.
6.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

  1. Replace electric throttle control actuator.
  2. Refer to Special Repair Requirement >> Inspection END

7.CHECK INTERMITTENT INCIDENT
Refer to See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Intermittent Incident.
>> Inspection END

Component Inspection
1.CHECK THROTTLE POSITION SENSOR

  1. Turn ignition switch OFF.
  2. Reconnect all harness connectors disconnected.
  3. Perform Special Repair Requirement.
  4. Turn ignition switch ON.
  5. Set selector lever to D position (CVT) or 1st position (M/T).

  

  1. Check the voltage between ECM harness connector terminals under the following conditions.

  

Is the Inspection result normal?
YES >> Inspection END
NO >> GO TO 2.
2.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

  1. Replace electric throttle control actuator.
  2. Go to Special Repair Requirement. >> Inspection END

Special Repair Requirement
1.PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Refer to See: Powertrain Management\Computers and Control Systems\Testing and Inspection\Programming and Relearning\Throttle Valve Closed Position Learning\Special Repair Requirement
>> GO TO 2.
2.PERFORM IDLE AIR VOLUME LEARNING
Refer to See: Engine, Cooling and Exhaust\Engine\Idle Speed\Testing and Inspection\Idle Air Volume Learning\Special Repair Requirement
>> END