Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » Powertrain Management » Fuel Delivery and Air Induction » Fuel Gauge Sender » Service and Repair  
 
 
  Service and Repair  
 

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY

Removal and Installation

REMOVAL

WARNING:
Read "General Precautions" before working on the fuel system. Refer to See: Service Precautions\Technician Safety Information\General Precautions.

  1. Unscrew the fuel filler cap to release the pressure inside the fuel tank.
  2. Release the fuel pressure from the fuel lines. Refer to (QR25DE For California), (QR25DE Except For California), See: Fuel Pressure\Testing and Inspection (VQ35DE).
  3. Disconnect the battery negative terminal.
  4. Remove the rear seat bottom. Refer to See: Body and Frame\Seats\Service and Repair\Removal and Replacement\Rear Seat\Removal And Installation\Coupe.

  

  1. Turn the four retainers 90° in a clockwise direction and remove the fuel pump Inspection hole cover.
  2. Disconnect the fuel level sensor, fuel filter, and fuel pump assembly electrical connector, EVAP hose quick connector, and the fuel feed hose quick connector from the fuel level sensor unit, fuel filter, and fuel pump assembly.

  

Remove the quick connector as follows:

  • Hold the sides of the connector, push in tabs and pull out the tube.

  

  • If the connector and the tube are stuck together, push and pull several times until they start to move. Then disconnect them by pulling.

CAUTION:

  • The tube can be removed when the tabs are completely depressed. Do not twist it more than necessary.
  • Do not use any tools to remove the quick connector.
  • Keep the resin tube away from heat. Be especially careful when welding near the tube.
  • Prevent acid liquid such as battery electrolyte, etc. from getting on the resin tube.
  • Do not bend or twist the tube during installation and removal.
  • Only when the tube is replaced, remove the remaining retainer on the tube or fuel level sensor, fuel filter, and fuel pump assembly.
  • When the tube or fuel level sensor, fuel filter, and fuel pump assembly is replaced, also replace the retainer with a new one (green colored retainer).

  

  • To keep the connecting portion clean and to avoid damage and foreign materials, cover them completely with plastic bags or something similar.
  1. Remove the lock ring using a socket drive handle and Tool as shown.

  

Tool number : KV991J0090 (J-46214)

CAUTION:

  • Discard the lock ring, do not reuse the lock ring.
  • Discard the ring seal, do not reuse the ring seal.

  

  1. Remove the fuel level sensor, fuel filter, and fuel pump assembly.

CAUTION:

  • Do not bend the float arm during removal.
  • Discard the ring seal, do not reuse the ring seal.

Inspection AFTER REMOVAL
Inspect the fuel level sensor, fuel filter, and fuel pump for any defects and foreign materials. Replace as necessary.

INSTALLATION
Installation is in the reverse order of removal.

  

  • Install the fuel level sensor, fuel filter, and fuel pump assembly with the fuel feed hose facing the front of the vehicle as shown. Use a new ring seal.
  • Connect the quick connector as follows:

  

  • Check the connection for damage or any foreign materials.
  • Align the connector with the tube, then insert the connector straight into the tube until a click is heard.
  • After the tube is connected, make sure the connection is secure by performing the following checks:
  • Pull the tube and the connector to make sure they are securely connected.
  • Visually confirm that the two retainer tabs are connected to the quick connector.

  

Inspection AFTER INSTALLATION
Use the following procedure to check for fuel leaks.

  1. Turn the ignition switch to ON (without starting the engine) to apply fuel pressure to the fuel system, then check the connections for fuel leaks.
  2. Start the engine and let it idle and check for fuel leaks at the fuel system connections.