NOTE: If DTC P0441 is displayed with other DTC such as P2122, P2123, P2127, P2128 or P2138, first perform trouble diagnosis for other DTC.
In this evaporative emission (EVAP) control system, purge flow occurs during non-closed throttle conditions.
Purge volume is related to air intake volume. Under normal purge conditions (non-closed throttle), the EVAP canister purge volume control solenoid valve is open to admit purge flow. Purge flow exposes the EVAP control system pressure sensor to intake manifold vacuum.
Under normal conditions (non-closed throttle), sensor output voltage indicates if pressure drop and purge flow are adequate. If not, a malfunction is determined.
DTC CONFIRMATION PROCEDURE 1.Inspection START
Will CONSULT-III be used?
Will CONSULT-III be used?
YES >> GO TO 2.
NO >> GO TO 6. 2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds. TESTING CONDITION:
Always perform test at a temperature of 5°C (41°F) or more.
>> GO TO 3. 3.PERFORM DTC CONFIRMATION PROCEDURE-I With CONSULT-III
Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and let it idle for at least 70 seconds.
Select "PURG FLOW P0441" of "EVAPORATIVE SYSTEM" in "DTC WORK SUPPORT" mode with CONSULT-III.
Touch "START". Is "COMPLETED" displayed on CONSULT-III screen?
YES >> GO TO 5.
NO >> GO TO 4. 4.PERFORM DTC CONFIRMATION PROCEDURE-II
When the following conditions are met, "TESTING" will be displayed on the CONSULT-III screen. Maintain the conditions continuously until "TESTING" changes to "COMPLETED". (It will take at least 35 seconds.)
CAUTION: Always drive vehicle at a safe speed. If "TESTING" does not change for a long time, retry from step 2.
Is "COMPLETED" displayed on CONSULT-III screen?
YES >> GO TO 5.
NO >> Perform DTC CONFIRMATION PROCEDURE again. GO TO 3. 5.PERFORM DTC CONFIRMATION PROCEDURE-III
Touch "SELF-DIAG RESULTS".
Which is displayed on CONSULT-III screen?
OK >> Inspection END
NG >> Go to Diagnosis Procedure. 6.PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to Component Function Check.
NOTE:
Use component function check to check the overall monitoring function of the EVAP control system purge flow monitoring. During this check, a 1st trip DTC might not be confirmed.
Is the Inspection result normal?
YES >> Inspection END
NO >> Go to Diagnosis Procedure.
Component Function Check 1.PERFORM COMPONENT FUNCTION CHECK Without CONSULT-III
Lift up drive wheels.
Start engine (ESP switch OFF) and warm it up to normal operating temperature.
Turn ignition switch OFF, wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF, wait at least 10 seconds.
Start engine and wait at least 70 seconds.
Set voltmeter probes to ECM harness connector terminals under the following conditions.
Check EVAP control system pressure sensor value at idle speed and note it.
Establish and maintain the following conditions for at least 1 minute.
Verify that EVAP control system pressure sensor value stays 0.1 V less than the value at idle speed (measured at step 6) for at least 1 second. Is the Inspection result normal?
YES >> Inspection END
NO >> Go to Diagnosis Procedure.
Diagnosis Procedure 1.CHECK EVAP CANISTER
Turn ignition switch OFF.
Check EVAP canister for cracks. Is the Inspection result normal?
YES-1 >> With CONSULT-III: GO TO 2.
YES-2 >> Without CONSULT-III: GO TO 3.
NO >> Replace EVAP canister. 2.CHECK PURGE FLOW With CONSULT-III
YES >> GO TO 5.
NO >> Repair EVAP purge line. 5.CHECK EVAP PURGE HOSE AND PURGE PORT
Disconnect purge hoses connected to EVAP service port A and EVAP canister purge volume control solenoid valve B.
Blow air into each hose and EVAP purge port C.
Check that air flows freely. Is the Inspection result normal?
YES-1 >> With CONSULT-III: GO TO 6.
YES-2 >> Without CONSULT-III: GO TO 7.
NO >> Repair or clean hoses and/or purge port. 6.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE With CONSULT-III
Start engine.
Perform "PURG VOL CONT/V" in "ACTIVE TEST" mode with CONSULT-III. Check that engine speed varies according to the valve opening. Does engine speed vary according to the valve opening?
YES >> GO TO 8.
NO >> GO TO 7. 7.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Refer to See: P0443.
Is the Inspection result normal?
YES >> GO TO 8.
NO >> Replace EVAP canister purge volume control solenoid valve. 8.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR
Disconnect EVAP control system pressure sensor harness connector.
Check that water is not inside connectors. Is the Inspection result normal?
YES >> GO TO 9.
NO >> Replace EVAP control system pressure sensor. 9.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR FUNCTION
Refer to See: P0452 for DTC P0452, See: P0453 for DTC P0453.
Is the Inspection result normal?
YES >> GO TO 10.
NO >> Replace EVAP control system pressure sensor. 10.CHECK RUBBER TUBE FOR CLOGGING
Disconnect rubber tube connected to EVAP canister vent control valve.
Check the rubber tube for clogging. Is the Inspection result normal?
